Hello:
I have a problem with a GE LightSpeed Ultra recently installed. When starting the system the computer stays at "OC Initializing. Please wait" and it stays there. After a few minutes the computer shuts down by itself. Apparently it loads the Applications, menus and everything seems to be there. After performing a Reconfiguration without regenerating the Data Base I can even see images,but same case, after a few minutes the computer shuts down. I have ran the Octane Diagnostics with the IRIX CD and all tests passed, hinv identifies disks and I ran also the ICE tests, first time ICE tests were run they all passed, second time the data marked an Error. So far I have tried to avoid software reload or Reconfiguration regenerating the Data Base. Any sugestions or tips will be appreciated. Thanks
Best regards,
Elias
Maybe you have bad sector on HDD. So you need to connect this HDD to another computer and test by special program. I usually use HDD regenerator- this program can repaired bad sectors.
I think this can help
Regards
Yes, Hardware initialization is completed, I can even move the table, rotate Gantry for centering lights, tilt. No scans can be performed as I don't have access to anything having to do with scanning in the computer. thanks,
Best Regards,
Elias
re: re: re: re: Re: GE LightSpeed Ultra initializing problem
August 28, 2012 03:45
Thank you, I made LFC twice, it seems to be fixed, but I'm having an artifact problem with this system, may I email you about it? Mine is johnnyb@tigo.com.py
I have the same case but I have not communication with the gantry. No ping with STC or ETC. I required a new Scan Disk (the original one is damaged) and a new transceiver because I do have not a valid way to test it trusty. No laser, no cough move, no changes in gantry leds during initialization
ZRG Medical closeout auctions take place on DOTmed.com. Bid today on 180 lots of medical equipment. Inspection is by appointment only. Please contact 760-438-8835 ext. 100 for an appointment.
Elias Valdes
GE LightSpeed Ultra initializing problem
September 02, 2010 01:05
Hello:
I have a problem with a GE LightSpeed Ultra recently installed. When starting the system the computer stays at "OC Initializing. Please wait" and it stays there. After a few minutes the computer shuts down by itself. Apparently it loads the Applications, menus and everything seems to be there. After performing a Reconfiguration without regenerating the Data Base I can even see images,but same case, after a few minutes the computer shuts down. I have ran the Octane Diagnostics with the IRIX CD and all tests passed, hinv identifies disks and I ran also the ICE tests, first time ICE tests were run they all passed, second time the data marked an Error. So far I have tried to avoid software reload or Reconfiguration regenerating the Data Base. Any sugestions or tips will be appreciated. Thanks
Best regards,
Elias
to rate and post a comment
Artem Potiy
Re: GE LightSpeed Ultra initializing problem
September 02, 2010 01:46
Dear Elias Valdes
Maybe you have bad sector on HDD. So you need to connect this HDD to another computer and test by special program. I usually use HDD regenerator- this program can repaired bad sectors.
I think this can help
Regards
Artem
to rate and post a comment
Josip Vujnovic
Re: GE LightSpeed Ultra initializing problem
September 15, 2010 09:51
Do you have communication with Gantry?
to rate and post a comment
Elias Valdes
Re: GE LightSpeed Ultra initializing problem
September 16, 2010 02:24
Yes, Hardware initialization is completed, I can even move the table, rotate Gantry for centering lights, tilt. No scans can be performed as I don't have access to anything having to do with scanning in the computer. thanks,
Best Regards,
Elias
to rate and post a comment
Josip Vujnovic
Re: GE LightSpeed Ultra initializing problem
September 16, 2010 03:56
Have you tried open DARC with telnet?
I had the same problem, with the same symptoms as you when I was a failure of DARC!
to rate and post a comment
Johnny Barreto
re: Re: GE LightSpeed Ultra initializing problem
August 27, 2012 03:12
How did you fix this problem? i'm having same issue by now
to rate and post a comment
Elias Valdes
re: re: Re: GE LightSpeed Ultra initializing problem
August 27, 2012 08:31
I replaced IG Board. Perform IG Diagnostics to know if it is good or faulty.
to rate and post a comment
Elias Valdes
re: re: re: Re: GE LightSpeed Ultra initializing problem
August 28, 2012 03:18
Don't forget to check also the SGI Octane or Octane2 compuyer
to rate and post a comment
Johnny Barreto
re: re: re: re: Re: GE LightSpeed Ultra initializing problem
August 28, 2012 03:45
Thank you, I made LFC twice, it seems to be fixed, but I'm having an artifact problem with this system, may I email you about it? Mine is johnnyb@tigo.com.py
to rate and post a comment
Jose Morillo
re: Re: GE LightSpeed Ultra initializing problem
November 13, 2023 10:54
I have the same case but I have not communication with the gantry. No ping with STC or ETC. I required a new Scan Disk (the original one is damaged) and a new transceiver because I do have not a valid way to test it trusty. No laser, no cough move, no changes in gantry leds during initialization
to rate and post a comment