Luiz Antonio Viana
AGFA service password
March 06, 2017 08:50
I need service password for AGFA CR 30-Xm
Since now! Thank you for helping everyone!
to rate and post a comment
re: AGFA service password
March 12, 2017 10:29
Check your e-mail
re: re: AGFA service password
September 29, 2017 05:18
I need service password for AGFA CR 10-X
re:re: re: AGFA service password
September 30, 2017 04:47
Hi friend you need password for cr10
September 29, 2017 05:17
September 30, 2017 04:45
can you send to me the service password for me
October 17, 2017 09:33
hello, could you send me the service password? email@example.com
March 15, 2018 04:12
Can I get the password too?
ESSeddik Moulai ali
re: re: re: AGFA service password
October 16, 2018 08:19
Can I get the password please?
October 16, 2018 08:23
Can I get the password please, I have patients waiting and I'm using the old method to develop my exams, help !!
February 26, 2019 10:17
I would like to get this password too my email is firstname.lastname@example.org
May 26, 2019 12:06
can you help me? I need service password for AGFA CR30-X
Thank a lot!
May 27, 2019 10:45
First or second generation. First generation there isnt a service password. Second gen there is. However for first generation you just login to windows as the designated service account and open the cr30x interface program.
Thinh Pham Van
June 20, 2019 09:42
Please send me: email@example.com. Thank you so much
Can i get the password too please?
October 25, 2018 12:06
What service password do you need?
And why do you need the service password, just curious?
Are you having problems or need to reconfigure something?
What system do you have, version NX?
What digitizer CR10, CR15, CR30, CR25, CR35, CR75, CR85, DXG?
Being an AGFA Platinum dealer I cannot legally give you any passwords but I can lend assistance remotely.
email me at firstname.lastname@example.org
October 25, 2018 07:12
Hi, i need the password to acces to the digitizer config (192.192....), my problem that is the queue is full of dicom image and even the ip is unknow to me because i have reset the config and need the network info of the digitizer, i have NX 3 i guess on windows 7, the digitizer is CR10-X, all its ok for me i have all the documentation to resolve my problem all I need is this problem, its the second week without it, please help me ð
re: re: re: re: AGFA service password
October 25, 2018 08:48
If you can get teamviewer installed on the NX workstation I can assist you.
The queue is not in the digitizer it is normally in NX under main menu queue management.
email me at email@example.com with your teamviewer information.
Let me backup, how did you reset the configuration?
Did you change your workstation IP Address?
The 184.108.40.206 address is a factory default and normally gets changed on installation to match your clinic subnet.
The only way to change the ip address successfully is with the cpf file or through the gui.
Again, email me with teamviewer id and password so I can remote in and assist.
I'm on eastern standard time and won't be available to assist until after 6pm.
re: re: re: re: re: AGFA service password
June 20, 2019 11:07
It appears individuals requesting passwords don't know what they have. They consider the NX workstation the digitizer (CR10, 12, 15, 30, 25, 35, 75, 85, DXG, DXS, DXM). What they fail to realize is they have two totally separate pieces of a system.
It would be nice if they would at least describe the problem that they are having and why they need the passwords to NX or digitizer.
You can cause a whole lot of trouble for yourself if you don't know what you are doing with these systems. Most of us who service these pieces of equipment have trained at AGFA for at least 2 weeks.
My recommendation to you all is get properly trained before you totally screw up a system that you know nothing about.
We are the best choice for all your Endoscopy needs. We have Certified Pre-Owned refurbished and used Endoscopes, and all other related components and
accessories. We are committed to your absolute satisfaction. (513) 469-7267