Re: Xenon Nova 20131520, Karl Storz Service Manual
January 05, 2010 02:01
Hi Laiq,
Did you get the service manual?.
I have a xenon Nova in Peru that is not working, this equipment works in a poor people Hospital so it´s important to me to get this manual too.
Thanks,
Re: Xenon Nova 20131520, Karl Storz Service Manual
October 11, 2011 01:11
Hi, what's the problem with the unit? It's so simple, that almost impossible to be something wrong. I'm former service engineer from KS and have been repaired such devices several times.
tell me what it does (or what it doesn't) and I'll try to help.
Victor
Re: Xenon Nova 20131520, Karl Storz Service Manual
January 17, 2012 09:31
Hi Humberto Machado
I have storz telicame singal chip camera cable
PCB canecter (canect to Camera cansol)Pin NO 4 (UP) mark side is No canect to any canecter .My cable is defectiv you Know about cable canection?
Jatin joshi
india
Re: Xenon Nova 20131520, Karl Storz Service Manual
March 28, 2012 03:04
Hi, I have this unit with a problem, the unit starts but the lamp don´t start.I have measure all diodes, and transistors , but cannot find the problem.The suplly is ok(153v), and the supply of Ic`s are in 5v.
Please can you help me?
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 26, 2013 03:19
Dear edson, the problem can be 2 defective capacitors, i had this a few times. They are in ignition-circuit, blue, 2,2nf, 7500V. Rework isolations arround after changing!
good luck. Holger
re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 08, 2014 09:39
Hello Holger,
I pulled those 2 caps, and they tested OK on my meter, but I am ordering 2 new ones anyways.
So here is a question... The 2 diodes near those caps, what are they? Both of mine seem open. They only have a numerical marking of 72 with 2 dots under them. Their component number are D601 and D602. But I still cant get a manual :( so I do not have access to a schematic that might say more
re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 10, 2014 10:38
Dear Joseph, i didnt have defective diodes in the ignition-circuit till now. The diodes are high-voltage-types and you cant test with normal diode-tester, with this they are open, but i think they are o.k. There exists 2 or 3 different boards from xenon175. One type has a diac and a diode. Last week i had the first time a defective ignition-transformer. You have to measure an secondary side of the transformer with a high-voltag-probe. The ignition-voltage must be higher 5000V. in my case ist was only 3000 V and there was no ignition. good luck
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 22, 2013 09:05
HELLO
Dear Victor,
I need help, could you send me the service manual for Xenon Nova 20131520 ?. I will apreciate this so much.
thanks, in advance.
Luis
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
September 04, 2018 10:51
Hi. I have a xenon nova 175, and Q7 is in short circuit. So I replaced this FET and I´ve tried to find any component damage, but i cannot find anything. So,If I changed the FET and turn on, the set after 3 seconds, damage the Q7 again.Do you have any idea what's going on? Thanks
re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
May 22, 2019 09:55
Hi. I have the same problem as edson amadeu. I'm changing damaged FET Q7 and after using the device some period it is damaging again. If you guide me what I have to do I will be apriciated. My e-mail is erenarikan@gmail.com
re: Xenon Nova 20131520, Karl Storz Service Manual
March 07, 2014 11:01
Dear Sir, I have xenon nova 20131520 light source. I have problem with board i guess, when i switch on the light source, fan inside is running but bulb is not glowing, please help me on this.. where might be the problem is? I HOPE YOU WOULD HAVE SEEN THIS KIND OF PROBLEM BEFORE.. AWAITING FOR YOUR REPLY..
re: Xenon Nova 20131520, Karl Storz Service Manual
October 06, 2014 03:46
I know this is a very old post, but I didn't think I should make a new one on the same subject. Does anyone have the service manual they can email me?
Thanks a bunch if you do!
Joseph
re: re: Xenon Nova 20131520, Karl Storz Service Manual
October 07, 2014 05:59
Dear all, i need the service-manual too, please can somebody help us? I have the problem, that the ignition voltage is with 2kv too low, so the lamp doesnt ignite. The capacitors are not the reason in this case (like a few other cases). The Lamp Voltage is with 158 V DC o.k. Perhaps we have a defective ignition-transformer, but i dont have a same part to compare. Thank you Holger
re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
January 30, 2015 10:57
Good afternoon Holger,
I was never able to find schematics for the light source, sorry I can't help you out with that.
As for the capacitors, did you change them for new ones already? I tested mine and they tested ok on my meter with the right capacitance, but they were still the cause of the problem. If you have not replaced them with brand spakin new ones, I would highly recommend that you do before other components.
I hope this helps, it was my personal experience.
Joseph
re: re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
August 07, 2015 07:35
I am also looking for service manual and/or schematics diagrams. My equipment does turn on, but the lamp does not. No led light turns on front display, except one that is inside, small yellow led in PCB, keeps blinking like some kind of alarm or something. Upon inspection, found that the fan was not working, replaced it and works again(turns on when equipment is on). Also in the heatsink, saw that there is power resistor in one side, but saw that there are 2 cut cables and next to it is the heatsink with 2 screwdriver holes in it. I presume that there was another power resistor or other component, seems odd. Can you send picture of internal components from one of your equipments to see if its missing something. Equipment seems that has been manipulated by third party. PCB and components seems fine at visual inspection. Tomorrow i'll check rest of components. Do you have any suggestions what might be?
re: re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
February 03, 2015 05:49
I am glad that you got it all sorted out! Sorry that I could not be more help. Thanks for all the help you did give me! The system that I was working on is still up and running.
re: Xenon Nova 20131520, Karl Storz Service Manual
August 07, 2015 07:35
I am also looking for service manual and/or schematics diagrams. My equipment does turn on, but the lamp does not. No led light turns on front display, except one that is inside, small yellow led in PCB, keeps blinking like some kind of alarm or something. Upon inspection, found that the fan was not working, replaced it and works again(turns on when equipment is on). Also in the heatsink, saw that there is power resistor in one side, but saw that there are 2 cut cables and next to it is the heatsink with 2 screwdriver holes in it. I presume that there was another power resistor or other component, seems odd. Can you send picture of internal components from one of your equipments to see if its missing something. Equipment seems that has been manipulated by third party. PCB and components seems fine at visual inspection. Tomorrow i'll check rest of components. Do you have any suggestions what might be?
re: Xenon Nova 20131520, Karl Storz Service Manual
July 05, 2019 02:52
Hello everyone, my name in Mike and I have received a Storz Xenon Nova 20131520, with the problem that it does not turn on the light, this is what I have found and replaced, switching relay with burned coil, and the 3 mosfets , I have verified capacitors and apparently they are ok, the diodes d12-d13 are also ok, but I have no output, ok fuses, etc etc ... I searched the network for the service manual / block diagram or just the schematic but without result.
I would be very grateful if someone has it and could send it to my email meirabella@ibermansa.com
Again, thank you very much and I apologize for the inconvenience
ElsMed engineers are located in four different countries. 24 hour response time to any service call. Service agreement provided for end-users range from a 6 month period to a 3 year period and covers all system spare parts.
(2)
(2)
Laiq Ahmed
Xenon Nova 20131520, Karl Storz Service Manual
June 23, 2009 01:10
Dear All.
I am looking for Xenon Nova 20131520, Karl Storz Light source service manual or schematics diagrams.
Thanks in advance.
Regards
LAIQ
to rate and post a comment
Milan Janca
Re: Xenon Nova 20131520, Karl Storz Service Manual
June 23, 2009 08:02
Try this link
https://www.karlstorz.com/cps/rde/xchg/SID-66403E2B-AF49A7B9/karlstorz-en/hs.xsl/2254.htm
to rate and post a comment
(2)
(2)
Laiq Ahmed
Re: Xenon Nova 20131520, Karl Storz Service Manual
June 24, 2009 07:22
Dear Milan
Thanks for your reply. But cant see the download link or any pdf link. Any explaination will be great. Thanks again.
to rate and post a comment
(1)
Geoff Hannis
Re: Xenon Nova 20131520, Karl Storz Service Manual
June 25, 2009 09:31
You probably need to Register, there, Mate.
Try that and see if Storz will send you the manual. You'll never know until you try!
Cheers.
to rate and post a comment
Enrique Moreno
Re: Xenon Nova 20131520, Karl Storz Service Manual
January 05, 2010 02:01
Hi Laiq,
Did you get the service manual?.
I have a xenon Nova in Peru that is not working, this equipment works in a poor people Hospital so it´s important to me to get this manual too.
Thanks,
to rate and post a comment
HUMBERTO MACHADO
Re: Xenon Nova 20131520, Karl Storz Service Manual
August 27, 2011 10:31
I need this service manual Xenon Nova 20131520!
please send me hmachadomoura@ig.com.br
thanks!!
to rate and post a comment
(3)
(7)
Victor Kolchenko
Re: Xenon Nova 20131520, Karl Storz Service Manual
October 11, 2011 01:11
Hi, what's the problem with the unit? It's so simple, that almost impossible to be something wrong. I'm former service engineer from KS and have been repaired such devices several times.
tell me what it does (or what it doesn't) and I'll try to help.
Victor
to rate and post a comment
jatin joshi
Re: Xenon Nova 20131520, Karl Storz Service Manual
January 17, 2012 09:31
Hi Humberto Machado
I have storz telicame singal chip camera cable
PCB canecter (canect to Camera cansol)Pin NO 4 (UP) mark side is No canect to any canecter .My cable is defectiv you Know about cable canection?
Jatin joshi
india
to rate and post a comment
edson amadeu
Re: Xenon Nova 20131520, Karl Storz Service Manual
March 28, 2012 03:04
Hi, I have this unit with a problem, the unit starts but the lamp don´t start.I have measure all diodes, and transistors , but cannot find the problem.The suplly is ok(153v), and the supply of Ic`s are in 5v.
Please can you help me?
Thanks
to rate and post a comment
(8)
Holger Fritze
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 26, 2013 03:19
Dear edson, the problem can be 2 defective capacitors, i had this a few times. They are in ignition-circuit, blue, 2,2nf, 7500V. Rework isolations arround after changing!
good luck. Holger
to rate and post a comment
(11)
(1)
Joseph Hughes
re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 08, 2014 09:39
Hello Holger,
I pulled those 2 caps, and they tested OK on my meter, but I am ordering 2 new ones anyways.
So here is a question... The 2 diodes near those caps, what are they? Both of mine seem open. They only have a numerical marking of 72 with 2 dots under them. Their component number are D601 and D602. But I still cant get a manual :( so I do not have access to a schematic that might say more
to rate and post a comment
(8)
Holger Fritze
re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 10, 2014 10:38
Dear Joseph, i didnt have defective diodes in the ignition-circuit till now. The diodes are high-voltage-types and you cant test with normal diode-tester, with this they are open, but i think they are o.k. There exists 2 or 3 different boards from xenon175. One type has a diac and a diode. Last week i had the first time a defective ignition-transformer. You have to measure an secondary side of the transformer with a high-voltag-probe. The ignition-voltage must be higher 5000V. in my case ist was only 3000 V and there was no ignition. good luck
to rate and post a comment
(11)
(1)
Joseph Hughes
re: re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 10, 2014 04:34
alright, Thanks. Also, which one is the ignition-transformer? The one with the big wrappings on it?
to rate and post a comment
Gausiano
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
November 22, 2013 09:05
HELLO
Dear Victor,
I need help, could you send me the service manual for Xenon Nova 20131520 ?. I will apreciate this so much.
thanks, in advance.
Luis
to rate and post a comment
Ibrahim
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
January 30, 2015 09:12
Dear Victor, i am looking for the service manual of this xenon nova 20131520, would you be so kind to share it with me? Ibrahim Boakye
to rate and post a comment
(1)
edson amadeu
re: Re: Xenon Nova 20131520, Karl Storz Service Manual
September 04, 2018 10:51
Hi. I have a xenon nova 175, and Q7 is in short circuit. So I replaced this FET and I´ve tried to find any component damage, but i cannot find anything. So,If I changed the FET and turn on, the set after 3 seconds, damage the Q7 again.Do you have any idea what's going on? Thanks
to rate and post a comment
(3)
(7)
Victor Kolchenko
re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
September 20, 2018 08:58
give me your email
to rate and post a comment
Eren ARIKAN
re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual
May 22, 2019 09:55
Hi. I have the same problem as edson amadeu. I'm changing damaged FET Q7 and after using the device some period it is damaging again. If you guide me what I have to do I will be apriciated. My e-mail is erenarikan@gmail.com
to rate and post a comment
Vasanth Kumar Gunalan
re: Xenon Nova 20131520, Karl Storz Service Manual
March 07, 2014 11:01
Dear Sir, I have xenon nova 20131520 light source. I have problem with board i guess, when i switch on the light source, fan inside is running but bulb is not glowing, please help me on this.. where might be the problem is? I HOPE YOU WOULD HAVE SEEN THIS KIND OF PROBLEM BEFORE.. AWAITING FOR YOUR REPLY..
Thanks in advance
Kumar
to rate and post a comment
Nadeem Iqbal M.Iqbal
re: re: Xenon Nova 20131520, Karl Storz Service Manual
February 01, 2019 09:27
any response from any side ?
to rate and post a comment
(11)
(1)
Joseph Hughes
re: Xenon Nova 20131520, Karl Storz Service Manual
October 06, 2014 03:46
I know this is a very old post, but I didn't think I should make a new one on the same subject. Does anyone have the service manual they can email me?
Thanks a bunch if you do!
Joseph
to rate and post a comment
(8)
Holger Fritze
re: re: Xenon Nova 20131520, Karl Storz Service Manual
October 07, 2014 05:59
Dear all, i need the service-manual too, please can somebody help us? I have the problem, that the ignition voltage is with 2kv too low, so the lamp doesnt ignite. The capacitors are not the reason in this case (like a few other cases). The Lamp Voltage is with 158 V DC o.k. Perhaps we have a defective ignition-transformer, but i dont have a same part to compare. Thank you Holger
to rate and post a comment
(11)
(1)
Joseph Hughes
re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
January 30, 2015 10:57
Good afternoon Holger,
I was never able to find schematics for the light source, sorry I can't help you out with that.
As for the capacitors, did you change them for new ones already? I tested mine and they tested ok on my meter with the right capacitance, but they were still the cause of the problem. If you have not replaced them with brand spakin new ones, I would highly recommend that you do before other components.
I hope this helps, it was my personal experience.
Joseph
to rate and post a comment
(1)
Vic
re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
February 01, 2015 10:21
Contact me directly at biktop@email.cz
to rate and post a comment
Alain Amador Mancera Leyva
re: re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
August 07, 2015 07:35
I am also looking for service manual and/or schematics diagrams. My equipment does turn on, but the lamp does not. No led light turns on front display, except one that is inside, small yellow led in PCB, keeps blinking like some kind of alarm or something. Upon inspection, found that the fan was not working, replaced it and works again(turns on when equipment is on). Also in the heatsink, saw that there is power resistor in one side, but saw that there are 2 cut cables and next to it is the heatsink with 2 screwdriver holes in it. I presume that there was another power resistor or other component, seems odd. Can you send picture of internal components from one of your equipments to see if its missing something. Equipment seems that has been manipulated by third party. PCB and components seems fine at visual inspection. Tomorrow i'll check rest of components. Do you have any suggestions what might be?
to rate and post a comment
(8)
Holger Fritze
re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
February 01, 2015 10:24
dear joseph, problem was the ignition transformer, with another use transformer its o.k. In other cases there were the capacitors defective.
to rate and post a comment
(11)
(1)
Joseph Hughes
re: re: re: re: re: Xenon Nova 20131520, Karl Storz Service Manual
February 03, 2015 05:49
I am glad that you got it all sorted out! Sorry that I could not be more help. Thanks for all the help you did give me! The system that I was working on is still up and running.
to rate and post a comment
Alain Amador Mancera Leyva
re: Xenon Nova 20131520, Karl Storz Service Manual
August 07, 2015 07:35
I am also looking for service manual and/or schematics diagrams. My equipment does turn on, but the lamp does not. No led light turns on front display, except one that is inside, small yellow led in PCB, keeps blinking like some kind of alarm or something. Upon inspection, found that the fan was not working, replaced it and works again(turns on when equipment is on). Also in the heatsink, saw that there is power resistor in one side, but saw that there are 2 cut cables and next to it is the heatsink with 2 screwdriver holes in it. I presume that there was another power resistor or other component, seems odd. Can you send picture of internal components from one of your equipments to see if its missing something. Equipment seems that has been manipulated by third party. PCB and components seems fine at visual inspection. Tomorrow i'll check rest of components. Do you have any suggestions what might be?
to rate and post a comment
(1)
abed ismail
re: Xenon Nova 20131520, Karl Storz Service Manual
February 07, 2018 07:27
i will appreciate it if you send me service manual
storz xenon nova 20134020 or any similar model
i have a problem where every time i start it the fuses gets burnt and the first 2 power transistor too even after repalcement
to rate and post a comment
Mike Eirabella
re: Xenon Nova 20131520, Karl Storz Service Manual
July 05, 2019 02:52
Hello everyone, my name in Mike and I have received a Storz Xenon Nova 20131520, with the problem that it does not turn on the light, this is what I have found and replaced, switching relay with burned coil, and the 3 mosfets , I have verified capacitors and apparently they are ok, the diodes d12-d13 are also ok, but I have no output, ok fuses, etc etc ... I searched the network for the service manual / block diagram or just the schematic but without result.
I would be very grateful if someone has it and could send it to my email meirabella@ibermansa.com
Again, thank you very much and I apologize for the inconvenience
to rate and post a comment