BV 300 has error "DFI Application not started, software inconsistant or not loadable". We dont have manuals or software for this system. Can someone contact me that can either load software for me or assist me in doing so. Thanks
re: BV 300 C-Arm Error DFI Application Not Started
July 15, 2015 06:29
first enter service mode and see carm ip address and configure laptop to static ip within the BV network scheme and connect to service port using crossover cable and then reboot carm for connection using explorer and connect using the target "carm"Ip address.This will connect you to a working dfi.There are other ways to connect but you probably want to consider calling Philips
re: re: BV 300 C-Arm Error DFI Application Not Started
July 16, 2015 08:15
I figured that software needs reloading but do not have software and am being told by Philips that the system was end of life in 2010 so they don't have software either.
re: re: re: BV 300 C-Arm Error DFI Application Not Started
July 17, 2015 09:52
That is not true, i haved same proble 1 month ago and the sofware is allready to load,if you have the license original of your C arm ,you can do the reloading
re: BV 300 C-Arm Error DFI Application Not Started
July 16, 2015 08:15
You need reload sofware ,for this you need software called X-Scope also need too know the license number for this BV300 and also need license to use X-Scoipe or hardware key.
I assume that you dont have any.
re: BV 300 C-Arm Error DFI Application Not Started
September 30, 2015 11:27
I could use some guidance in the DFI software reload process. I installed XScope, connected, entered fault finding and ran the BIST without issue, but when I attempt to install the DFI software The error I receive indicates "No lower sections for this item" leaving me to believe I need a hardware key; Is the hardware key universal to all units or do you need one that matches your serial number? And where do you locate your Software license key? Your assistance is appreciated. Happy to send a gift card or other fair compensation.
Titanium Medical Imaging, specializing in Toshiba/Canon Equipment Sales, Parts, and Service. Parts are in stock and available for immediate delivery. In-Room MRI Upgrades available now. ph:713-640-5457 or kyle@titaniummed.com
(1)
JB
BV 300 C-Arm Error DFI Application Not Started
July 15, 2015 04:39
BV 300 has error "DFI Application not started, software inconsistant or not loadable". We dont have manuals or software for this system. Can someone contact me that can either load software for me or assist me in doing so. Thanks
to rate and post a comment
(2)
john eurith
re: BV 300 C-Arm Error DFI Application Not Started
July 15, 2015 06:29
first enter service mode and see carm ip address and configure laptop to static ip within the BV network scheme and connect to service port using crossover cable and then reboot carm for connection using explorer and connect using the target "carm"Ip address.This will connect you to a working dfi.There are other ways to connect but you probably want to consider calling Philips
to rate and post a comment
(3)
(16)
Ari Lipson
re: BV 300 C-Arm Error DFI Application Not Started
July 15, 2015 06:29
you need to reload software. A headache!
where are you located?
to rate and post a comment
(11)
Jerry Beeler
re: re: BV 300 C-Arm Error DFI Application Not Started
July 16, 2015 08:15
I figured that software needs reloading but do not have software and am being told by Philips that the system was end of life in 2010 so they don't have software either.
to rate and post a comment
(5)
ricardo Usandivaras
re: re: re: BV 300 C-Arm Error DFI Application Not Started
July 17, 2015 09:52
That is not true, i haved same proble 1 month ago and the sofware is allready to load,if you have the license original of your C arm ,you can do the reloading
to rate and post a comment
(16)
(2)
bashir ahmad
re: re: re: re: BV 300 C-Arm Error DFI Application Not Started
January 28, 2016 04:09
Hi dear from where can i check this licence no please.
to rate and post a comment
(2)
Ed Herry
re:re: re: re: BV 300 C-Arm Error DFI Application Not Started
April 23, 2018 04:08
Hi, can u show me how to reload.
to rate and post a comment
(1)
lefort
re: re: BV 300 C-Arm Error DFI Application Not Started
July 24, 2017 10:39
In cameroon
to rate and post a comment
(5)
ricardo Usandivaras
re: BV 300 C-Arm Error DFI Application Not Started
July 16, 2015 08:15
You need reload sofware ,for this you need software called X-Scope also need too know the license number for this BV300 and also need license to use X-Scoipe or hardware key.
I assume that you dont have any.
to rate and post a comment
(7)
Saqib Mirza
re: BV 300 C-Arm Error DFI Application Not Started
July 16, 2015 08:16
Contact at saqib.mirzapk@gmail.com
to rate and post a comment
Scott Fishman
re: BV 300 C-Arm Error DFI Application Not Started
September 30, 2015 11:27
I could use some guidance in the DFI software reload process. I installed XScope, connected, entered fault finding and ran the BIST without issue, but when I attempt to install the DFI software The error I receive indicates "No lower sections for this item" leaving me to believe I need a hardware key; Is the hardware key universal to all units or do you need one that matches your serial number? And where do you locate your Software license key? Your assistance is appreciated. Happy to send a gift card or other fair compensation.
to rate and post a comment